1
JEE Advanced 2019 Paper 1 Offline
MCQ (More than One Correct Answer)
+4
-1
Let us consider a system of units in which mass and angular momentum are dimensionless. If length has dimension of L, which of the following statement(s) is/are correct?
A
The dimension of force is [L]-3
B
The dimension of power is [L]-5
C
The dimension of energy is [L]-2
D
The dimension of linear momentum is [L]-1
2
JEE Advanced 2016 Paper 2 Offline
MCQ (More than One Correct Answer)
+4
-2
In an experiment to determine the acceleration due to gravity g, the formula used for the time period of a periodic motion is $$T = 2\pi \sqrt {{{7\left( {R - r} \right)} \over {5g}}} $$. The values of R and r are measured to be (60 $$ \pm $$ 1) mm and (10 $$ \pm $$ 1) mm, respectively. In five successive measurements, the time period is found to be 0.52 s, 0.56 s, 0.57 s, 0.54 s and 0.59 s. The least count of the watch used for the measurement of time period is 0.01 s. Which of the following statement(s) is(are) true?
A
The error in the measurement of r is 10 %
B
The error in the measurement of T is 3.57 %
C
The error in the measurement of T is 2 %
D
The error in the determined value of g is 11 %
3
JEE Advanced 2016 Paper 1 Offline
MCQ (More than One Correct Answer)
+3
-1
A length-scale (l) depends on the permittivity ($$\varepsilon $$) of a dielectric material, Boltzmann constant (kB), the absolute temperature (T), the number per unit volume (n) of certain charged particles, and the charge (q) carried by each of the particles. Which of the following expression(s) for I is(are) dimensionally correct?
A
$$l = \sqrt {\left( {{{n{q^2}} \over {\varepsilon {k_b}T}}} \right)} $$
B
$$l = \sqrt {\left( {{{\varepsilon {k_b}T} \over {n{q^2}}}} \right)} $$
C
$$l = \sqrt {\left( {{{{q^2}} \over {\varepsilon {n^{2/3}}{k_B}T}}} \right)} $$
D
$$l = \sqrt {\left( {{{{q^2}} \over {\varepsilon {n^{1/3}}{k_B}T}}} \right)} $$
4
JEE Advanced 2015 Paper 1 Offline
MCQ (More than One Correct Answer)
+4
-2
Consider a Vernier callipers in which each 1 cm on the main scale is divided into 8 equal divisions and a screw gauge with 100 divisions on its circular scale. In the Vernier callipers, 5 divisions of the Vernier scale coincide with 4 divisions on the main scale and in the screw gauge, one complete rotation of the circular scale moves it by two divisions on the linear scale. Then:
A
If the pitch of the screw gauge is twice the least count of the Vernier callipers, the least count of the screw gauge is 0.01 mm.
B
If the pitch of the screw gauge is twice the least count of the Vernier callipers, the least count of the screw gauge is 0.005 mm.
C
If the least count of the linear scale of the screw gauge is twice the least count of the Vernier callipers, the least count of the screw gauge is 0.01 mm.
D
If the least count of the linear scale of the screw gauge is twice the least count of the Vernier callipers, the least count of the screw gauge is 0.005 mm.
JEE Advanced Subjects