A one shell pass, one tube-pass heat exchanger, has counter flow configuration between the shell side and tube side fluids. The total number of tubes within the heat exchanger is $$10$$ and the tube dimensions are $$ID=10$$ $$mm,$$ $$OD=12$$ $$mm$$ and length $$=1m.$$ saturated dry steam enters the shell side at a flow rate of $$2$$ $$kg/s$$ and the temp of $${100^ \circ }C.$$ In the tube side, cold water enters at a flow rate of $$10$$ $$kg/s$$ with an inlet temp of $${25^ \circ }C.$$ The $$OHTC$$ based on the outer surface area of the tubes is $$50$$ $$W/{m^2}K.$$ The specific heat of water is $$4.18$$ $$kJ/kg$$-$$K$$ and the latent heat of steam is $$2500$$ $$kJ/kg.$$ What is the condition of the steam at the exit.

In shell and tube heat exchanger, baffles are mainly used to

An object has the shape of cubical box of side $$10cm,$$ with no top cover. The box is placed inside a room whose dimensions are much larger than those of the box. All the five surfaces of box are at a temp of $${500^ \circ }C$$ and have an emissivity of $$0.6.$$ The walls of the room are at $${25^ \circ }C$$ and have an emissivity of $$0.4.$$ All these surfaces can be assumed to be diffuse-gray. Find the net radiative heat loss from the inner surface of the box to the walls of the room.
Stephen Boltzmann constant $$5.67 \times {10^{ - 8}}\,\,W/{m^2}{K^4}$$. View factor between two parallel square plates placed directly opposite to each other is $$0.2$$

A diffuse radiation surface has

Biot number signifies

Match the property with their units

Property
$$A.$$ Bulk modulus
$$B.$$ Thermal conductivity
$$C.$$ Heat transfer coefficient
$$D.$$ Heart flow rate

Units
$$1.$$ $$W/s$$
$$2.$$ $$N/{m^2}$$
$$3.$$ $$N/{m^3}$$
$$4.$$ $$W$$
$$5.$$ $$W/mK$$
$$6.$$ $$W/{m^2}K$$

When the annual demand of a product is $$24000$$ units, the $$EOQ$$ (Economic Order Quantity) is $$2000$$ units. If the annual demand is $$48000$$ units the most appropriate $$EOQ$$ will be

Strength to weight ratio for a circuit shaft transmitting power is directly proportional to the

Match the roling element bearings with the most appropriate loading condition

Bearing - type
(a)$$\,\,\,\,\,\,$$ Ball bearing
(b)$$\,\,\,\,\,\,$$ Roller bearing
(c)$$\,\,\,\,\,\,$$ Needle bearing
(d)$$\,\,\,\,\,\,$$ Taper roller bearing

Loading condition
(p)$$\,\,\,\,\,\,$$ Tangential load
(q)$$\,\,\,\,\,\,$$ Radial load
(r)$$\,\,\,\,\,\,$$ Heavy radial load with impact
(s)$$\,\,\,\,\,\,$$ Light radial load with space limitation
(t)$$\,\,\,\,\,\,$$ Heavy radial and axial load
(u)$$\,\,\,\,\,\,$$ Fatigue load

For a pinion of $$15$$ teeth, under cutting ____________( increases / decreases) with _______________(increases / decreases ) of pressure angle.

In a shaft with a transverse hole, as the hole to the shaft diameter ratio ___________ (increases / decreases), the torsional stress concentration factor__________ (increases/decreases)

When there is no room temp change, the total shrinkage allowance on a pattern is INDEPENDENT OF

A bush was turned after mounting the same on a mandrel. The mandrel diameter in millimeters is $${40^{\matrix{ { + 0.00} \cr { - 0.05} \cr } }}$$ and bore diameter of bush is $${40^{\matrix{ { + 0.06} \cr { - 0.00} \cr } }}$$.

The maximum eccentricity of the bush, in $$mm$$ will be

Wrinkling is a common defect found in

For cutting double start screw threads of pitch $$1.0$$ $$mm$$ on a lathe, the thread cutting tool should have a feed rate of

Match the products and their manufacturing process

A milling cutter having $$10$$ teeth is rotating at $$100$$$$rpm$$. The table feed is set at $$50mm$$ per minute. The feed per tooth in $$mm$$ is

Find the percentage change in cutting speed required to give a $$50\% $$ reduction in tool life (that is required tool life is half of the original tool life ) when the value of the tool life exponent $$n=0.125$$ or $$1/8$$.

Determine the Merchants constant $$'C'$$ (shear angle relation) for aluminium from the following orthogonal machining data. Rake angle $${35^ \circ }$$ and an uncut chip thickness $$0.15mm,$$ the values of $${F_c}$$ and $${F_t}$$ are found to be $$200$$ and $$90$$ $$N$$ respectively. The average chip thickness is also measured and found to be $$0.3$$ $$mm,$$ width of cut $$2.5mm$$ and cutting velocity $$30m/min.$$

Calculate the $$MRR$$ and Specific cutting pressure for the following cutting conditions
Work material : steel,
Tool material : $$HSS,$$
Depth of cut : $$1.6mm,$$
Feed : $$0.8mm/rev$$
Cutting speed $$=5.5m/min$$ and power consumed $$=0.67$$ $$kW$$

Most of the metal cutting heat goes into the

For gas welding a particular job using a neutral oxy-acetylene flame the acetylene consumption was $$10$$ ltrs. The oxygen consumption from the cylinder in liters will be

A strip of thickness $$T$$ $$mm$$ is rolled in a $$2$$ high single pass rolling mill, having roll diameter $$D$$ $$mm,$$ to a final thickness of $$\left( {T - 2\Delta T} \right)mm.$$ If the friction coefficient between the roll and strip is $$\mu ,$$ calculate the maximum reduction $$2\Delta T$$ possible in this operation. Using this relation, for $$D=300mm,$$ $$T=40mm$$ and friction coefficient is $$0.3,$$ calculate the outgoing thickness of the strip. If the inlet velocity is $$5m/s,$$ what is the outgoing strip velocity?.

A falk consisting of a cope and drag has the following dimensions: length $$300mm,$$ width $$200mm,$$ and total septh $$200mm$$ (cope height $$50mm$$).
A $$150mm\,\, \times \,100mm\,\, \times 50mm$$ cast iron block is to be cast. If the specific weight of cast iron is $$78\,\,kN/{m^3}$$ and that of the mold sand $$16\,\,kN/{m^3}$$, find lifting force on the cope created by buoyant force, weight of sand in the cope, the net force at the liquid-sand interface and additional weight to be kept on the cope.

Converging passage is used for feeding the liquid molten metal into the mould to

In a single heater regenerative cycle, steam enters the turbine at $$30$$ bar, $${300^0}C$$ and condenser pressure is $$0.096$$ bar. The feed water heater is a direct contact type which operates at $$5$$ bar. Draw flow and $$h$$-$$s$$ diagrams considering the condition of steam at entry to the heater in mixture region. Calculate steam extracted from heater to turbine in $$kg$$ per $$kg$$ of steam flow the cycle and cycle efficiency. The enthalpies of steam at different locations of the cycle are given in a table below. Pump work may neglected.

Velocity compounded steam turbine known as ___________ (Curtis / Rateau ) turbine uses the principle of converting entire __________ (pressure / velocity) energy before entering the first stage runner itself.

In a Rankine cycle heat is added

A $$7MW$$ hydro turbine working under a head of $$10$$ $$m$$ at a rotational speed of $$125$$ $$rpm$$ is to be designed and developed by conducting model tests in a laboratory. Maximum possible discharge to the model is $$600$$ liters per second at a constant head of $$5m.$$ Determine the minimum scale of the model and its speed if the expected efficiency of the model is $$85\% .$$