ExamSIDE
Questions (Powered by ExamGOAL)
Electrical and Electronics Measurement
Basic of Indicating Instruments
Marks 1Marks 2Marks 5
Error Analysis and Measurement
Marks 1Marks 2
Measurement of Resistance and A.C Bridges
Marks 1Marks 2
Measurement of Energy and Power
Marks 1Marks 2Marks 5
Digital Voltmeters Questions
Marks 1Marks 2
Potentiometer and Instrument Transformers
Marks 1Marks 2
Cathode Ray Oscilloscope
Marks 1Marks 2Marks 3
Previous Next
1
GATE EE 2013
MCQ (Single Correct Answer)
+2
-0.6
A strain gauge forms one arm of the bridge shown in the figure below and has a nominal resistance without any load as $$\,{R_s} = 300\Omega .$$ Other bridge resistance are $$\,{R_1} = {R_2} = {R_3} = 300\Omega .\,\,$$ The maximum permissible current through the strain gauge is $$20$$ $$mA.$$ During certain measurement when the bridge is excited by maximum permissible voltage and the strain gauge resistance is increased by $$1$$% over the nominal value, the output voltage $${V_0}$$ in $$mV$$ is GATE EE 2013 Electrical and Electronics Measurement - Measurement of Resistance and A.C Bridges Question 7 English
A
$$56.02$$
B
$$40.83$$
C
$$29.85$$
D
$$10.02$$
2
GATE EE 2010
MCQ (Single Correct Answer)
+2
-0.6
The Maxwell's bridge shown in the fig. is at balance, the parameters of the inductive coil are GATE EE 2010 Electrical and Electronics Measurement - Measurement of Resistance and A.C Bridges Question 8 English
A
$$R = {{{R_2}{R_3}} \over {{R_4}}}\,\,\,\,L = {C_4}{R_2}{R_3}$$
B
$$L = {{{R_2}{R_3}} \over {{R_4}}}\,\,\,\,R = {C_4}{R_2}{R_3}$$
C
$$R = {{{R_4}} \over {{R_2}{R_3}}}\,\,\,\,L = {1 \over {{C_4}{R_2}{R_3}}}$$
D
$$L = {{{R_4}} \over {{R_2}{R_3}}}\,\,\,\,R = {1 \over {{C_4}{R_2}{R_3}}}$$
3
GATE EE 2008
MCQ (Single Correct Answer)
+2
-0.6
The ac bridge shown in the figure is used to measure the impedance $$Z.$$ If the bridge is balanced for oscillator frequency $$f=2$$ $$kHz$$, then the impedance $$Z$$ will be GATE EE 2008 Electrical and Electronics Measurement - Measurement of Resistance and A.C Bridges Question 3 English
A
$$\left( {260 + j0} \right)\,\Omega $$
B
$$\left( {0 + j200} \right)\,\Omega $$
C
$$\left( {260 - j200} \right)\,\Omega $$
D
$$\left( {260 + j200} \right)\,\Omega $$
4
GATE EE 2008
MCQ (Single Correct Answer)
+2
-0.6
A bridge circuit is shown in the figure below. Which one of the sequence given below is most suitable for balancing the bridge? GATE EE 2008 Electrical and Electronics Measurement - Measurement of Resistance and A.C Bridges Question 4 English
A
First adjust $${R_4},$$ and then adjust $${R_1}$$
B
First adjust $${R_2},$$ and then adjust $${R_3}$$
C
First adjust $${R_2},$$ and then adjust $${R_4}$$
D
First adjust $${R_4},$$ and then adjust $${R_2}$$
Previous Next
Questions Asked from Marks 2
GATE EE 2025 (1) GATE EE 2015 Set 1 (1) GATE EE 2014 Set 3 (1) GATE EE 2013 (1) GATE EE 2010 (1) GATE EE 2008 (2) GATE EE 2006 (1) GATE EE 2003 (1)
GATE EE Subjects
Electromagnetic Fields
Signals and Systems
Engineering Mathematics
General Aptitude
Power Electronics
Power System Analysis
Analog Electronics
Control Systems
Digital Electronics
Electrical Machines
Electric Circuits
Electrical and Electronics Measurement