A balanced Wheatsone bridge ABCD has the following arm resistances :

R_AB = 1 k$$\Omega$$ $$\pm$$ 2.1%; R_BC = 100 $$\Omega$$ $$\pm$$ 0.5%; R_CD is an unknown resistance; R_DA = 300 $$\Omega$$ $$\pm$$ 0.4%. The value of R_CD and its accuracy is

When the Wheatstone bridge shown in the figure is used to find the value of resistor $${R_x},$$ the galvanometer $$G$$ indicates zero current when $${R_1} = 50\,\Omega ,\,\,{R_2} = 65\,\Omega $$ and $$\,{R_3} = 100\,\Omega ,\,\,$$ If $${R_3}$$ is known with $$\, \pm 5\% \,$$ tolerance on its nominal value of $$100\,\Omega .$$ What is the range of $${R_x}$$ in Ohms?

The bridge method commonly used for finding mutual inductance is

The bridge circuit shown in the fig below is used for the measurement of an unknown element Z_x. The bridge circuit is best suited when Z_x is a

Kelvin double bridge is best suited for the measurement of

A Kelvin double bridge is best suited for the measurement of

In the Wheatstone bridge shown below, the sensitivity of the bridge in terms of change in balancing voltage $E$ for unit change in the resistance $R$, in $\mathrm{mV} / \Omega$, is _________ (round off to two decimal places)

An unbalanced $$DC$$ Wheatstone bridge is shown in the figure. At what value of $$p$$ will the magnitude of $${V_0}$$ be maximum?

In the bridge circuit shown, the capacitors are loss free. At balance, the value of capacitance C₁ in microfarad is ________.

A strain gauge forms one arm of the bridge shown in the figure below and has a nominal resistance without any load as $$\,{R_s} = 300\Omega .$$ Other bridge resistance are $$\,{R_1} = {R_2} = {R_3} = 300\Omega .\,\,$$ The maximum permissible current through the strain gauge is $$20$$ $$mA.$$ During certain measurement when the bridge is excited by maximum permissible voltage and the strain gauge resistance is increased by $$1$$% over the nominal value, the output voltage $${V_0}$$ in $$mV$$ is

The Maxwell's bridge shown in the fig. is at balance, the parameters of the inductive coil are

The ac bridge shown in the figure is used to measure the impedance $$Z.$$ If the bridge is balanced for oscillator frequency $$f=2$$ $$kHz$$, then the impedance $$Z$$ will be

A bridge circuit is shown in the figure below. Which one of the sequence given below is most suitable for balancing the bridge?

$${R_1}$$ and $${R_2}$$ are the opposite arms of $${R_3}$$ and $${R_4}$$ of a wheat stone bridge. The source voltage is applied across $${R_1}$$ and $${R_3}$$ under balanced conditions, which one of the following is true?

The items in List $$-$$ $${\rm I}$$ represent the various types of measurements to be made with a reasonable accuracy using a suitable bridge. The items in List $$-$$ $${\rm II}$$ represent the various bridges available for this purpose. Select the correct choice of the item in List $$-$$ $${\rm II}$$ for the corresponding item in List $$-$$ $${\rm I}$$ from the following.

List $$-$$ $${\rm I}$$
$$A.$$ Resistance in the milli Ohm range
$$B.$$ Low values of Capacitance
$$C.$$ Comparison of resistances which are nearly equal
$$D.$$ Inductance of a coil with a large time $$-$$ constant

List $$-$$ $${\rm II}$$
$$1.$$ Wheatstone Bridge
$$2.$$ Kelvin Double Bridge
$$3.$$ Schering Bridge
$$4.$$ Wien's Bridge
$$5.$$ Hay's Bridge
$$6.$$ Carry $$-$$ Foster Bridge